Question: How Should A Lift Operator Travel?

What is the most important safety device on a forklift?

5 most important safety devices on a forkliftBrakes.

Brakes are the absolute most important safety feature on any motorized vehicle.

Seatbelts.

All powered industrial lift trucks manufactured after 1992 are required to have a restraint system or enclosure of some kind, according to OSHA Director John B.

Overhead guards.

Lights.

Horn..

How much can a 5000 lb forklift lift?

A 5,000-lb. capacity forklift will lift that much weight up to 48-inch forks (with a 24-inch load center) but going out to 60 inches (with a 30-inch load center), for example, drops the capacity to 4,000 pounds.

What direction should the lift be driven down a ramp when carrying a load?

Traveling down ramp with a load. Requirements and Recommended Practices: When traveling with a load, the load should point up the incline, regardless of direction of travel.

For example, if your forklift is traveling at 7 mph, it will take you about 16 feet to make a complete stop. If you are traveling at 9 mph, your stopping distance increases to 21 feet. The average car, on the other hand, can come to a stop in 20 feet when traveling much faster at 20 mph.

What is the lift trucks rated capacity?

Forklift capacities range from about 3,000 lbs up to more than 70,000+ lbs. You can find the rated capacity of a forklift on its data plate. OSHA requires “only loads within the rated capacity of a truck shall be handled.” It’s easy to think the rated capacity is the same as maximum capacity, but it’s not that simple.

What actions should be taken when driving a forklift?

Stay Safe While Using A Forklift Ensure both forks are as far under the load as possible before lifting. Drive with the load as low as safely possible. Pay attention to posted speed limits and warning signs. Always look in the direction you’re traveling; if a load blocks the view ahead, travel in reverse.

How long does it take to stop a lift truck that is traveling at full speed?

And when they are carrying heavy payloads, forklifts can take even further to stop. If a forklift is traveling 7 miles per hour, it can take the operator approximately 16 feet to stop the vehicle completely in an emergency. Increase that speed to 9 mph and it can take more than 21 feet to stop.

What is the best thing to do if your lift truck starts to tip over?

If the forklift is tipping over, protect yourself by staying put:Stay in your seat and do not attempt to jump off.Lean away from the falling direction of the lift.Hold onto the steering wheel and make sure you’re stable.

What will make the load more stable during travel?

When traveling with a load, always make sure to tilt the mast of the forklift backward so that the load will firmly place against the backrest to make it more secure during transport. By doing this, you move the center of gravity towards to rear of the forklift making it more secure when traveling.

What should you check before lifting a load?

Check that the overhead clearance is adequate before raising loads. Do not raise or lower the fork unless the lift truck is stopped and braked. Lift loads straight up or tilt back slightly. Do not lift a load that extends above the load backrest unless no part of the load can possibly slide back toward the operator.

When traveling load load should I lift?

Lower the load so that its lowest point is 15 to 20 cm (6 to 8 inches) from the floor. While traveling, keep the load at a safe travel height.

How many pallet lengths should you leave for a safe stopping distance?

The safe traveling distance between forklifts is approximately three truck lengths, or about a time lapse of three seconds when passing the same point. More specifically, it’s about 20 feet between forklifts. The three-second rule is the same for automobiles on the road and is just as important for forklifts.

What should safe lifting training include?

Training should include general principles of ergonomics, recognition of hazards and injuries, procedures for reporting hazardous conditions, and methods and procedures for early reporting of injuries. Additionally, job specific training should be given on safe work practices, hazards, and controls.

To avoid incidents while approaching the load, follow these requirements and recommendations:Always approach the load slowly and carefully.Stop 8-12 inches in front of the load.Make sure the truck is placed squarely in front of the load.Make sure the forks are at the correct height for lifting the load.More items…•

Which of the following will help you maintain control when stacking a load?

How do you maintain control when lifting, tilting, and stacking a load? Lift the load straight until it is clear, then tilt back. Watch that the load does not catch on adjacent loads or obstructions. Do not raise or lower the forks before you stop the lift truck and set the brakes.